Sluice motor took a dive |
Sluice motor took a dive |
Aug 1 2016, 07:48 AM
Post
#1
|
|
Shovel Buster! Group: Members Posts: 69 Joined: 11-July 15 From: Boulder CO Member No.: 120,999 |
A friend of mine was running his sluice and the motor took a dive in the creek and suddenly stopped working. Does anybody know what may be the problem? He let it sit for about an hour and let everything dry out, but it still never was able to start. Are these machines able to take on some water and maybe the engine just got flooded with gas?
Thank you all for the help. Adam |
|
|
Aug 1 2016, 12:53 PM
Post
#2
|
|
Rock Bar! Group: Members Posts: 875 Joined: 25-July 14 From: Westminster, CO Member No.: 117,949 |
I'm totally not an engine guy, but I'll throw out some food for thought.
The motor was submerged, or just stopped working? If not submerged, my first thought is to check the oil since that's what I've seen when mine won't start. Mine will also start chugging if the vibration is throwing up a lot of water near the carb. After that, I'd look at the plug and wires making sure the plug is ok and there is no water in the head. If it was submerged, the gas could have water in it, the carb likely needs to be cleaned, and you may have fouled your spark plug, wire or ignition coil. I'm kinda curious what kind of setup is it that you need a motor for a sluice? -------------------- Lifetime Member
opera non verba "All courses of action are risky, so prudence is not in avoiding danger (it's impossible), but calculating risk and acting decisively. Make mistakes of ambition and not mistakes of sloth. Develop the strength to do bold things, not the strength to suffer." ~Niccolò Machiavelli Ref Code: EM448 |
|
|
Aug 1 2016, 01:44 PM
Post
#3
|
|
Master Mucker! Group: Admin Posts: 4,149 Joined: 7-October 03 From: Colorado Member No.: 3 |
Hi Adam, that's a bummer about the motor dive in the creek. Does happen from time to time though.
Good answer Emac. I pictured it being a high banker set up with an engine setting on the bank pumping water to the unit, then it slid off the bank? I think the engine should be ok, but like Emac said, you will need to drain and dry out the fuel tank and carb as well as clean the plug and dry out the cylinder if needed. You may as well change out the oil too just to be safe, may not have gotten any water in the crankcase but since you're (he'll) be on project anyway, might as well do it up! Once the water is all drained/dried out of the system, I bet it'll fire right back up with a fresh tank of fuel. -------------------- CP-Owner/Administrator
www.ColoradoProspector.com IF YOU USE IT, THE GROUND PRODUCED IT! MINERS MAKE "IT" HAPPEN!! |
|
|
Aug 1 2016, 03:56 PM
Post
#4
|
|
Shovel Buster! Group: Members Posts: 69 Joined: 11-July 15 From: Boulder CO Member No.: 120,999 |
I'm totally not an engine guy, but I'll throw out some food for thought. The motor was submerged, or just stopped working? If not submerged, my first thought is to check the oil since that's what I've seen when mine won't start. Mine will also start chugging if the vibration is throwing up a lot of water near the carb. After that, I'd look at the plug and wires making sure the plug is ok and there is no water in the head. If it was submerged, the gas could have water in it, the carb likely needs to be cleaned, and you may have fouled your spark plug, wire or ignition coil. I'm kinda curious what kind of setup is it that you need a motor for a sluice? Sorry it's more like a dredge I guess. it is a pretty neat set up. The attached picture is the closet thing I can find that he has. The motor was submerged. Not 100% maybe 65%. I will pass that along to him. There very possibly could be water in the oil and the gas tank.
Attached image(s)
|
|
|
Aug 9 2016, 08:00 PM
Post
#5
|
|
Diggin' In! Group: Members Posts: 6 Joined: 8-August 05 Member No.: 273 |
Is that a 2 cycle or 4 cycle engine, where are you located?
|
|
|
Aug 10 2016, 10:29 AM
Post
#6
|
|
Shovel Buster! Group: Members Posts: 69 Joined: 11-July 15 From: Boulder CO Member No.: 120,999 |
|
|
|
Aug 12 2016, 09:17 PM
Post
#7
|
|
Diggin' In! Group: Members Posts: 6 Joined: 8-August 05 Member No.: 273 |
What sizes is it? I can take a look at if you want to bring it to Longmont, send me a number
|
|
|
Sep 11 2016, 05:46 PM
Post
#8
|
|
Shovel Buster! Group: Members Posts: 69 Joined: 11-July 15 From: Boulder CO Member No.: 120,999 |
|
|
|
Lo-Fi Version | Time is now: 19th April 2024 - 01:54 PM |